1.44 ST7735 display

[ART032]

Hi.
I can't undestend, how change code for use 1.44 ST7735
i see white screen color
WEB inerface works

PS: test adafrute_st7735 code - work

[locki-cz]

just edit lines like there: #51

[ART032]

I've already replaced the strings following this link, but it still doesn't work.
my modified code in the attachment.

Esp32_radio.zip

[locki-cz]

Here is my edit but it isnt last version, ididnt have time to play with my code for radio for months :(

ESP32-Radio_ST7735version.zip

[ART032]

it doas not work whis that code.

[locki-cz]

do you have this in defaultprefs.h? you can set ti via web interface, also 1,44" have smaller resolution, than 1,8"

pin_tft_cs = 15 # GPIO Pin number for TFT "CS"
pin_tft_dc = 2 # GPIO Pin number for TFT "DC"

[ART032]

yeas, thise is in defaultprefs.h. in the test adafruit sketh it works, but cut a part of text

a part of defaultprefs.h:

Clock offset and daylight saving time

clk_server = pool.ntp.org # Time server to be used
clk_offset = 1 # Offset with respect to UTC in hours
clk_dst = 1 # Offset during daylight saving time (hours)

Some IR codes

ir_40BF = upvolume = 2
ir_C03F = downvolume = 2

GPIO pinnings

pin_ir = 35 # GPIO Pin number for IR receiver VS1838B
pin_enc_clk = 25 # GPIO Pin number for rotary encoder "CLK"
pin_enc_dt = 26 # GPIO Pin number for rotary encoder "DT"
pin_enc_sw = 27 # GPIO Pin number for rotary encoder "SW"

pin_tft_cs = 15 # GPIO Pin number for TFT "CS"
pin_tft_dc = 2 # GPIO Pin number for TFT "DC"

sd_cs = 21 # GPIO Pin number for SD card "CS"

pin_vs_cs = 5 # GPIO Pin number for VS1053 "CS"
pin_vs_dcs = 16 # GPIO Pin number for VS1053 "DCS"
pin_vs_dreq = 4 # GPIO Pin number for VS1053 "DREQ"

[ART032]

debug:
no words about start tft ! why?
ets Jun 8 2016 00:22:57

rst:0x10 (RTCWDT_RTC_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:1
load:0x3fff0018,len:4
load:0x3fff001c,len:956
load:0x40078000,len:0
load:0x40078000,len:13256
entry 0x40078a90

D: Starting ESP32-radio running on CPU 1 at 240 MHz. Version Mon, 05 Mar 2018 10:52:00 GMT. Free memory 171056
D: Partition nvs found, 20480 bytes
D: Read 6 keys from NVS
D: pin_ir set to -1
D: pin_enc_clk set to -1
D: pin_enc_dt set to -1
D: pin_enc_sw set to -1
D: pin_tft_cs set to -1
D: pin_tft_dc set to -1
D: pin_sd_cs set to -1
D: pin_vs_cs set to 5
D: pin_vs_dcs set to 16
D: pin_vs_dreq set to 4
D: pin_shutdown set to -1
D: pin_spi_sck set to 18
D: pin_spi_miso set to 19
D: pin_spi_mosi set to 23
D: GPIO0 is HIGH
D: GPIO2 is HIGH
D: GPIO4 is HIGH
D: GPIO5 is HIGH
D: GPIO12 is HIGH
D: GPIO13 is HIGH
D: GPIO14 is HIGH
D: GPIO15 is HIGH
D: GPIO16 is HIGH
D: GPIO17 is HIGH
D: GPIO18 is HIGH
D: GPIO19 is HIGH
D: GPIO21 is HIGH
D: GPIO22 is HIGH
D: GPIO23 is HIGH
D: GPIO25 is HIGH
D: GPIO26 is HIGH
D: GPIO27 is HIGH
D: GPIO32 is HIGH
D: GPIO33 is HIGH
D: GPIO34 is LOW, probably no PULL-UP
D: GPIO35 is LOW, probably no PULL-UP
D: Create list with acceptable WiFi networks
D: End adding networks
D: Scan Networks
D: Scan completed
D: Number of available networks: 2
D: 1 - Prosyst Signal: -67 dBm, Encryption ????,
D: 2 - PSGuest Signal: -67 dBm, Encryption WPA2_PSK,
D: End of list
D: Command: preset with parameter 0
D: Command: toneha with parameter 0
D: Command: tonehf with parameter 0
D: Command: tonela with parameter 0
D: Command: tonelf with parameter 0
D: Command: volume with parameter 0
D: Slow SPI, Testing VS1053 read/write registers...
D: VS1053 not properly installed!
D: Connect to WiFi
D: WiFi Failed! Trying to setup AP with name ESP32Radio and password ESP32Radio.
D: IP = 192.168.4.1
D: Start server for commands
D: Rotary encoder is disabled (-1/-1/-1)

[ART032]

Why prefs is -1 ????

[Edzelf]

The setting are missing in the preferences.
You may add them in the web interface like this:
pin_tft_cs = 15 # GPIO TFT CS
pin_tft_dc = 2 # GPIO TFT DC
pin_vs_cs = 5 # GPIO VS1053 CS
pin_vs_dcs = 16 # GPIO VS1053 DCS
pin_vs_dreq = 4 # GPIO VS1053 DREQ

[ART032]

I directly prescribed in the code PIN. everything worked.

struct iosetting klist[] = { // List of I/O related keys
{ "pin_ir", &ini_block.ir_pin, 35 },
{ "pin_enc_clk", &ini_block.enc_clk_pin, 25 },
{ "pin_enc_dt", &ini_block.enc_dt_pin, 26 },
{ "pin_enc_sw", &ini_block.enc_sw_pin, 27 },
{ "pin_tft_cs", &ini_block.tft_cs_pin, 15 },
{ "pin_tft_dc", &ini_block.tft_dc_pin, 2 },
{ "pin_sd_cs", &ini_block.sd_cs_pin, 21 },
{ "pin_vs_cs", &ini_block.vs_cs_pin, VS1053_CS },
{ "pin_vs_dcs", &ini_block.vs_dcs_pin, VS1053_DCS },
{ "pin_vs_dreq", &ini_block.vs_dreq_pin, VS1053_DREQ },
{ "pin_shutdown", &ini_block.vs_shutdown_pin, -1 },
{ "pin_spi_sck", &ini_block.spi_sck_pin, 18 },
{ "pin_spi_miso", &ini_block.spi_miso_pin, 19 },
{ "pin_spi_mosi", &ini_block.spi_mosi_pin, 23 },
{ NULL, NULL, 0 } // End of list

and I chose the right type of display:

tft->initR(INITR_144GREENTAB);