Repository navigation
Conversation
The T8152 (M6) Always-On Processor differs from the T8140 one: its setup port is not reachable from the AP, so it has one mailbox, and its audio service uses six serializer power domains and the jack, speaker and speaker-sense ADMAC channels. Signed-off-by: Thomas Glanzmann <thomas@glanzmann.de>
Add the Mac mini M6 (J873) sound card. Signed-off-by: Thomas Glanzmann <thomas@glanzmann.de>
The J873 (Mac mini M6) AOP runs the same firmware generation as T8140 (EPIC v4, iBoot-loaded, started by the AP), but the T8140 "setup port" is not reachable from the AP: mailbox 1 of the AOP's mailbox bank and the ADT aop-exclave-mailbox both bus-error. The firmware boots without it: RTKit protocol 12, then its "audio" EPIC service. Add apple,t8152-aop with the T8140 configuration minus the setup port, starting every advertised endpoint. Signed-off-by: Thomas Glanzmann <thomas@glanzmann.de>
The Mac mini (M6, J873) speaker runs a 250-BCLK TDM frame, which the SN012776's ratio auto-detection rejects. Describe the property that fixes the ratio instead. Signed-off-by: Thomas Glanzmann <thomas@glanzmann.de>
The J873 (Mac mini M6) AOP runs the speaker frame at 250 BCLKs of 12 MHz. The SN012776 cannot auto-detect that ratio and mutes with "fault: bad TDM clock". With TAS2764_CLK_CFG (register 0x60) set to 0x30 and TDM_CFG0 bit 6 set it accepts the frame and plays. Do that when the new ti,bclk-ratio property names the ratio; only this one ratio is supported. Source of the value: the register write was first seen in the macOS SN012776 driver; it is a single register value, and its effect (no fault, correct playback) was verified on J873 hardware. No table or code was taken from macOS. The field is initialised in probe, so non-OF matches keep auto-detection. Signed-off-by: Thomas Glanzmann <thomas@glanzmann.de>
The SDOUT1 mux offers the ASP receive channels as a source, but no DAPM route connected them, so selecting "ASP RX CH1" or "ASP RX CH2" left the capture path without an input. The J873 and J813 AOP audio services use it to loop the playback stream back. Signed-off-by: Thomas Glanzmann <thomas@glanzmann.de>
On T8152 (J873, Mac mini M6) the AOP firmware owns the audio fabric, as on T8140. Its "audio" EPIC service offers cout/cin (the CS42L84 jack, base-ns ADMAC TX5/RX5, MCA4) and spkr (the SN012776 speaker, TX1, MCA0). Each service is an ASoC back-end DAI: startup attaches it, requests pw0 (which raises the audio fabric) and powers the MCA leaves, all of which are required. pwrd starts the serializer clocks at prepare, before ASoC unmutes the codecs: the jack codec locks its PLL to the bit clock, and the speaker amplifier reports "bad TDM clock" whenever it runs without one. The jack restarts its clocks on every prepare so that a stream restarted after an underrun begins on a frame boundary; the mono speaker (one slot per frame) keeps them running. The front-ends are dmaengine PCMs on the base-ns channels: the jack in stereo, the speaker in mono (its serializer runs one 32-bit slot; stereo frames play at half pitch). The firmware's serializer configuration (property 701) is byte-identical to the one macOS publishes, so the driver leaves it alone. Signed-off-by: Thomas Glanzmann <thomas@glanzmann.de>
The J873 (Mac mini M6) uses the T8152 AOP audio driver as its CPU component: the CS42L84 jack on "cout" (DSP_A | IB_NF, one-BCLK sync pulse) and one SN012776 on "spkr" (I2S, NB_IF: data sampled on the rising edge, as macOS programs the amp). Each AOP front-end owns the DMA channel of one serializer, so the speaker can only be fed from the secondary front-end; the new spk_secondary_only sets the speaker mux accordingly, and spk_dai_fmt gives the speaker link its own format. There is no qualified speaker protection for J873 yet (no verified sense path, thermal model or power budget), so the speaker fails closed: it is only enabled with please_blow_up_my_speakers. Opted in, it runs as macOS runs it: amp gain 15 (ADT speaker-config) and no volume lock (safe_vol 0), since there is no sense stream for a protection daemon. The jack is not affected. Signed-off-by: Thomas Glanzmann <thomas@glanzmann.de>
The T8142 AOP keeps its crash buffer in its own slot of its DART stream and asks for it on endpoint 1 with that IOVA. A client without shmem_setup refused the request, so the firmware never got its crash buffer acknowledged. APPLE_RTKIT_FIRMWARE_OWNED_CRASHLOG takes such a buffer as the firmware's, without a CPU mapping, and acknowledges the request unchanged; a later crash is reported without a log. RtKit::new_with_firmware_crashlog() selects it at runtime, so a driver can use it for one SoC only. Signed-off-by: Thomas Glanzmann <thomas@glanzmann.de>
The T8142 AOP (MacBook Air J813) waits for the host on a setup port, as the T8140 one does: the ADT's aop-exclave-mailbox at 0x3d067c000 (AOP ASC + 0x4007c000, not behind the arm-io translation). Its EPMAP announces other service endpoints than T8140's fixed set (0x4, 0x20, 0x23 and 0x32 on J813), so take the endpoints that must get buffers from the EPMAP when the match data says so. The firmware places its own crash log buffer in its firmware-mapped DART slot; accept it as the firmware's, as for G17P. After the setup boot all AFK endpoints start, and with the audio fabric left to the firmware (see the J813 device tree) the firmware announces its "audio" EPIC service. Signed-off-by: Thomas Glanzmann <thomas@glanzmann.de>
Behind an AOP the serializer feeding a capture channel is the firmware's, and it stops in the middle of a frame whenever it likes. A capture that stays open across such stops (the speaker V/I sense, which a protection daemon reads for as long as it runs) then carries the partial frame forward: every later frame is off by its words, and the samples of one amplifier are read as another's. On the MacBook Air J813 one restart in three slipped by one 16-bit word. Let a client pass the frame size in bytes as a u32 in dma_slave_config.peripheral_config. A paused cyclic capture on such a channel resumes at the next frame boundary of its current period: the reports completed before the pause are accounted for, the rings are reset and the rest of the period is submitted from the aligned address, then whole periods as before. Without a frame size nothing changes. Signed-off-by: Thomas Glanzmann <thomas@glanzmann.de>
The J813 speaker stream (ADT iop-audio-controller/audio-speaker) differs from J873's: four SN012776 in 32-bit playback slots 0-3, and their voltage and current sense back on the same stream's RX side (base-ns RX0) as eight 16-bit slots. Make the speaker and sense shapes per-SoC match data: J873 keeps one playback channel; T8142 gets four, and an 8-channel S16_LE "Speaker Sense" front-end. The sense capture is the speaker serializer's RX, which the firmware stops anywhere in a frame. Before every `pwrd` of the speaker, restart a running sense capture at a frame boundary (apple-admac realignment, the partial frame reads as zeros), so that a protection daemon that keeps it open attributes each amplifier's voltage and current to the right one. The sense back-end also attaches the speaker service and requests `pw0 ` at startup: its front-end requests the ADMAC channel next, and the ADMAC only answers while the firmware holds the audio fabric up. Opening the sense before any other stream since the AOP started (speakersafetyd at boot) otherwise faults the bus. Signed-off-by: Thomas Glanzmann <thomas@glanzmann.de>
MacBook Air 13" M5 (T8142): as on J873 the AOP firmware owns the audio fabric and the CPU component is the T8152-style AOP audio driver. The jack is a CS42L84 on "cout", the speakers four SN012776 (one woofer and one tweeter per side) on "spkr", with their V/I sense on the same stream. As on the other SN012776 laptops the speaker volume stays locked until a protection daemon (speakersafetyd) holds it. Signed-off-by: Thomas Glanzmann <thomas@glanzmann.de>
The MacBook Air J813's three microphones are the AOP's "hpai" service (ADT iop-audio-controller/audio-hp-mic): the firmware runs the PDM part and delivers 48 kHz float32 frames of three channels (the ADT's audio-hp-mic-proxy description: 12 bytes per frame) on leap-s ADMAC RX0. There is no codec, so it gets a card of its own with one capture PCM, named like the other AOP microphone cards (AppleJ813HPAI, "MacBook Air J813 High-Power Audio Interface", driver aop_audio) so that the existing UCM and DSP configurations for those apply. As on T8140: open attaches the service and requests pw0 (which raises the LEAP fabric), powers the LEAP leaves (leap-s ADMAC, RX0, LEAP MCA), and only then requests the channel, whose registers fault without them. The trigger starts the DMA and queues pwrd behind it; started earlier, the LEAP produces into a channel nobody services. Close releases the channel, then pw0 and the leaves. The card exists only where the DT gives the LEAP power domains (all three); J873 is unchanged. The dmaengine substream setup moves into a helper shared with the ASoC front-ends. Tested on J813: a tone from the speakers reads -44 to -49 dBFS on all three channels, 70 dB over the quiet floor, exactly while it plays; PipeWire picks up the card with asahi-audio's J613 beamformer graph. Signed-off-by: Thomas Glanzmann <thomas@glanzmann.de>
integration/aurora added the nCal boot argument and word-wise boot-argument access to AopHwConfig. Both machine configurations keep the firmware's own boot arguments unchanged, so set ncal to zero and leave word access off. Signed-off-by: Thomas Glanzmann <thomas@glanzmann.de>
Every boot on the J616s logged "spi-nor spi0.0: supply vcc not found, using dummy regulator". The M1, M2, M3, J713 and J700 trees describe the flash's always-on PMU rail as a fixed regulator; the M4 Pro/Max tree came later and has none. Add the same regulator and point the flash at it. Signed-off-by: Ryan Murray <81541646+RyanTheTide@users.noreply.github.com> Assisted-by: LLM
Preserve current RTKit crashlog and GPU handling while retaining the expanded macaudio bindings and adding J813/J873 compatibles. Original audio commits and authorship are preserved.
…ation Test whether COUT standby supplies the missing cold-boot fabric setup. A muted zero-data jack stream permitted HPAI capture and subsequent capture-only opens on J813; standby without any playback is the next hardware qualification step. Preserve Thomas Glanzmann’s driver and adapt the T8140 DMA sync-stop pattern from Ryan Murray, also flushing queued HPAI work before DMA teardown. No LPAI buffer binding or codec unmute is performed.
…queue Describe the T8142 microphone DMA and LEAP power domains and card names in the shared audio binding. Queue sleeping firmware power requests on system_dfl instead of the deprecated system workqueue, as directed by the runtime warning observed during hardware capture tests.
…-initialization-20261106 ASoC: apple: integrate J813 audio with first-open microphone initialization
…616-nor-vcc arm64: dts: apple: t604x-j614-j616: Describe the boot NOR flash supply
Resolves sound/soc/apple/macaudio.c: aurora-wip added spk_dai_fmt and spk_secondary_only (J813/J873) where integration added tweeter_hpf_granted (speaker protection ownership); the struct keeps all three. Signed-off-by: Ryan Murray <81541646+RyanTheTide@users.noreply.github.com> Assisted-by: LLM
Signed-off-by: Ryan Murray <81541646+RyanTheTide@users.noreply.github.com> Assisted-by: LLM
…nc-20261107 Merge integration/aurora into aurora-wip (11-07)
Brings aurora-wip up to integration/aurora 068dfce: pcie-apple endpoint reset retry (aurora-silicon#1069) and the tools/aurora-sep PKGBUILD checksum fix (aurora-silicon#1068). Signed-off-by: Ryan Murray <81541646+RyanTheTide@users.noreply.github.com> Assisted-by: LLM
…n/wip-sync-20261107b aurora-wip <- integration/aurora 068dfce (aurora-silicon#1068, aurora-silicon#1069). Clean merge, W=1 pcie-apple.o 0 warnings on the merged tree, CI host-tests/rust-build/source pass. Merge train (MTR).
Brings aurora-wip up to the tested release branch: CTXR execmem (aurora-silicon#985, aurora-silicon#1079), KFIX speaker sleep and resume fixes (aurora-silicon#1077, aurora-silicon#1080), JPEG v2 (aurora-silicon#1072), Jonathan's G17 and USB work (aurora-silicon#1073-aurora-silicon#1076), brcmfmac flowring count (aurora-silicon#1081), ANE H16 startup restart (aurora-silicon#1066) and the Touch ID per-prompt match (aurora-silicon#904). Signed-off-by: Ryan Murray <81541646+RyanTheTide@users.noreply.github.com> Assisted-by: LLM
Adds the 11-07 evening batch: t8140 disabled SPI3/FPWM0/SPMI nodes (aurora-silicon#1034), J700 CPU zones (aurora-silicon#1043), J616C fans (aurora-silicon#1092) and the thunderbolt DP PM workqueue fix (aurora-silicon#1098). Signed-off-by: Ryan Murray <81541646+RyanTheTide@users.noreply.github.com> Assisted-by: LLM
…n/wip-sync-20261107c Gate on the exact head tree 6c684e8 (buildbox): fleet22-config Image+modules+dtbs build rc=0, 0 errors, 0 warnings, 5890 modules (= fleet); run-host-tests 193/193; apple-dcp host selftests 86/86 (fleet baseline 86/86). CI host-tests/source/rust-build green. Brings aurora-wip up to integration/aurora 810b92c.
Brings aurora-wip up to fleet25: DT descriptions (aurora-silicon#1029, aurora-silicon#1030, aurora-silicon#1112), the J715 board (aurora-silicon#1129), Stockholm NFC (aurora-silicon#1042, aurora-silicon#1136), the AV1 tile check (aurora-silicon#1100), the M4 Max ANE profile and AVD quirk (aurora-silicon#1088, aurora-silicon#1091), boot-log fixes (aurora-silicon#1103, aurora-silicon#1104) and the Neo ANE memory floor (aurora-silicon#1137). Conflicts: macaudio.c and apple,macaudio.yaml, where aurora-wip's J813 and J873 entries and integration's J715 entries were added at the same spot. Keep all of them. Signed-off-by: Ryan Murray <81541646+RyanTheTide@users.noreply.github.com> Assisted-by: LLM
Brings aurora-silicon#1215, the ADT coverage fix for boards that are new to the base. Signed-off-by: Ryan Murray <81541646+RyanTheTide@users.noreply.github.com> Assisted-by: LLM
Brings aurora-silicon#1194, which makes Touch ID wait for the first password after boot (kernel side). Signed-off-by: Ryan Murray <81541646+RyanTheTide@users.noreply.github.com> Assisted-by: LLM
…n/wip-sync-20261108b-mtr3 Merge train: sync aurora-wip with integration/aurora 6fee375
…silicon#1410) The binding and the J714c device tree name the AOP audio service "apple,t6050-aop-audio", but the driver matched only t8142 and t8152, so that node never bound. Add a T6050 hardware config. The J714c ADT audio-speaker stream header (DeviceTree.j714cap) has the same layout as J813's with six amplifiers in place of four: 6 speaker slots and 12 sense words (V, I per amplifier), at 16 bits, on slots vsense 0,4,..20 / isense 2,6,..22. J813's header has 4 slots, 8 sense words and vsense 0..12 / isense 2..14. HW_CFG_T8152 (one amplifier, two sense words) would expose the wrong channel counts, so it is not reused. The sense width and the sense realignment are taken from J813's config by analogy; they are not tested on a J714c. Tested: builds as a module with Rust enabled (clang 19, arm64 defconfig plus CONFIG_RUST, CONFIG_SND_SOC_APPLE_T8152_AOP_AUDIO=m); the object carries the apple,t6050-aop-audio match string. Not tested: no J714c boot, no sound.
fb8edd9 to
2fddae2
Compare
|
Heads-up: this stack (#1798, #1799, #1800) now conflicts with integration/aurora in Could you refresh #1797 onto the current integration/aurora and rebase the three on it? When resolving, please keep those two commits' interrupt-driven receive path as it is. We'll review the listed commits once the stack is mergeable again. |
2fddae2 to
e2555c5
Compare
|
Rebased onto the refreshed #1797 (ceade2e, on integration/aurora 292773f). The branch is now e2555c5 (was 2fddae2) and merges cleanly again.
The testing lines in the description are updated: |
e2555c5 to
814b959
Compare
|
Rebased onto the refreshed #1797 (d87e41e, on integration/aurora 514ae1f). The branch is now 814b959 (was e2555c5) and merges cleanly again. One commit is new: arm64: configs: asahi: build the T8152 ACIOPHY USB3 PHY. #1939 added With #1797 and the three J873g PRs, at 514ae1f: |
aurora-wip carries the J873g (Mac mini M6) hardware that integration lacks: aurora-silicon#1197 (ANS2 NVMe, 10GbE on apcie port 2, SMC power off/restart, watchdog, SPMI, USB2 hosts, audio DT) and the T8152 ADMAC layout. Resolutions: - sart: both sides added the same SART4 layout (T6050 on integration, T8152 on aurora-wip); keep integration's sart_ops_v4 and match both. - mailbox: keep integration's polled providers and its interrupt-driven receive for the T6050 GPU mailboxes (788441e, 41c359d), and add the J873 ANS post-office mailbox (rx_poll_required, j873_window) next to them. It receives through the T8152 ASCWrap v8 poller. - nvme: integration's reset_optional replaces aurora-wip's optional_reset; keep the T6050 and T8152 tables. - pcie: keep power-domain attach and the T8152 MRRS limit. - admac: keep the T6050 display ADMAC and add the T8152 layout; the descriptor id goes into the flags word; the resume path is integration's. - aop.rs, macaudio.c, t8152_aop_audio.rs, tas2764.[ch], sound Kconfig: integration's versions, which already carry the T8152/J873 commits and extend them (T8142, T6050). Dropped from aurora-wip with them: aurora-silicon#1410 (integration matches T6050 itself) and the system_dfl workqueue switch of ad4910c. - bindings: list both sides' compatibles. In apple,mailbox.yaml interrupts are required unless the mailbox is polled: integration's secure-rtbuddy-proxy or aurora-wip's T8152 ANS mailbox, which describes none. In apple,nvme-ans.yaml resets and power domains are required unless the controller is the T6050's or the T8152's, and integration's apple,sleep-wake-delay-ms stays T6050-only. Signed-off-by: Thomas Glanzmann <thomas@glanzmann.de>
814b959 to
b6c31d8
Compare
|
Rebased onto the refreshed #1797 (bbfdefa, on integration/aurora 0abc2f3). The branch is now b6c31d8 (was 814b959) and merges cleanly again. Booted on the M6 with the rebased stack: "apple-aciophy-usb3 383000000.phy: USB3 up", and both front-port hubs run at 10000 Mb/s. DT and host checks are as on #1797. |
|
Thanks for getting USB3 up on the M6 front ports. 10 Gbit/s to the hub is a nice result. Two things before this can go in. First, we avoid a second implementation of a mechanism the tree already has. Second, the file header and the comment near line 148 name macOS driver classes and functions. Please describe the sequence by its registers and steps only, with no reference to macOS internals. When it lives in |
…mailboxes On T8152 the NVMe (ANS), display (DCP), keyboard and trackpad (MTP) and SEP coprocessors talk through windows of the same post-office block as the SMC: counted FIFOs sharing one status register, with interrupt masking left to the interrupt controller. The register layout is the one apple,t8152-smc-mailbox already describes. Add a compatible per coprocessor, each with apple,t8152-smc-mailbox as its fallback, so the existing driver match serves them without a code change and a later difference can still be keyed on the specific compatible. All four carry traffic on a MacBook Pro (M6, J804), with the single-compatible form of these nodes: NVMe, the keyboard and trackpad, and Touch ID run through them, and the DCP driver exchanges its messages through the DCP window. Signed-off-by: LiamRay11 <228416644+LiamRay11@users.noreply.github.com> Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com> [Thomas: taken from aurora-silicon#2105 for the J873g ANS node; placed before the T8152 ASCWrap v8 entry this branch adds] Signed-off-by: Thomas Glanzmann <thomas@glanzmann.de>
Describe the J873g ANS post-office mailbox as the J804 does: with apple,t8152-smc-mailbox as the fallback compatible and the window's send-empty and recv-not-empty interrupts. The ADT's ans node lists interrupts 302, 262, 222 and 1349 (the last is NVMe's, nvme-interrupt-idx 3). Every post-office mailbox's list starts with 299 + its msgbox-mailbox-num and 259 + that number, and for the SMC (760, 759) and the DCP (304, 264) mailboxes, which run on their interrupts on the J873g, the first is send-empty and the second recv-not-empty. Signed-off-by: Thomas Glanzmann <thomas@glanzmann.de>
The J873g ANS node now carries apple,t8152-smc-mailbox as its fallback and describes its interrupts, so the SMC mailbox's match data serves it on its interrupts, as it serves the J804's. Remove the profile that polled both directions without interrupts: its match entry, the rx_poll_required and j873_window fields, and the machine and fixed address check in probe. Signed-off-by: Thomas Glanzmann <thomas@glanzmann.de>
…ilbox The J873g ANS mailbox is now described with the apple,t8152-smc-mailbox fallback and its interrupts. Remove the standalone, interrupt-less apple,t8152-ans-mailbox entry and its conditions. Signed-off-by: Thomas Glanzmann <thomas@glanzmann.de>
The front USB-C ports of the Mac mini (2026, J873g) sit behind an on-board USB3 hub. The hub is wired to the Type-C PHY (ACIOPHY) of the SoC's ATC2 directly, without a Type-C mux or port controller in between, so the PHY only ever runs in one fixed USB3 configuration. Describe the PHY in that role. Besides its own register block it needs the PIPE handler of its DWC3 controller, which selects whether the controller's PIPE interface is fed by the ACIOPHY or by the controller's internal dummy PHY, and the PMGR power states and PSD block of the ATC that have to be up before the PHY can be powered. The register tunables come from the PHY's node in Apple's device tree. Signed-off-by: Thomas Glanzmann <thomas@glanzmann.de>
b6c31d8 to
1906255
Compare
The J873g's front USB-C ports sit behind an on-board VL822 hub wired to ATC2's PHY directly, without a Type-C mux. So far the hub ran at USB2 only: the bootloader leaves the PHY powered down and the PIPE handler on the controller's dummy PHY. Bring the PHY up in USB3 mode: its PMGR dependencies, the ACIOPHY power-up, efuse/PLL tunables, crossbar 0x110, fabric, PLL, USBC and lane tunables, PHY reset release. Then switch the PIPE handler from the dummy PHY to the ACIOPHY, holding the MAC's PIPE reset and power-down through the PHY's BIST overrides meanwhile. The PMGR dependencies are the ATC's DP_0, DP_1 and USB_AON power states and its common PSD domain. There is no T8152 power domain driver for them, so the PHY powers those it finds off and turns only those back off again. The power-up expects the PHY in the clamped power-down state the bootloader leaves it in, and the PIPE lock handshake is only acknowledged while the controller is out of reset. Power up lane 0 explicitly: without it the lane registers stay in AHB reset, drop their tunables and the PHY never reports PIPE PhyStatus. With it the hub enumerates at 10 Gb/s on the J873g. With the earlier linux-aurora j873 version of this driver, a USB 3 gigabit NIC behind the hub ran at 5 Gb/s and 873 Mbit/s with iperf3. Signed-off-by: Thomas Glanzmann <thomas@glanzmann.de>
The two front USB-C ports sit behind an on-board VL822 hub on usb-drd2. The hub's USB2 side is on the controller's eUSB2 PHY, which the loader sets up, and its USB3 side on ATC2's Type-C PHY, wired directly without a Type-C mux. So far the controller was limited to high speed and the hub ran at USB2 only. Describe ATC2's PHY in USB3 mode, hand it to usb-drd2 as its USB3 PHY and drop the controller's high-speed limit. Nothing changes for usb-drd1 (the back-left port). PS and PSD are ATC2's DP_0/DP_1/USB_AON power states and its common PSD domain (ADT clock-gates 57). The tunables are the groups of the ADT's atc-phy2 node (26A434) that apply to USB3 on lane 0. Some of them differ between the four ATCs of the same machine, so they likely carry per-device calibration. Signed-off-by: Thomas Glanzmann <thomas@glanzmann.de>
The Mac mini (M6, J873g) front ports reach their USB3 hub through the T8152 ACIOPHY USB3 PHY. Build it beside the other Apple PHYs, as the shared defaults require of every native driver. Signed-off-by: Thomas Glanzmann <thomas@glanzmann.de>
1906255 to
6e2ae8b
Compare
|
Thanks. I've done the second point. The head is now
No functional change: the driver builds with no W=1 warnings, and the diff is comments only. I agree with the first point, moving the PHY into |
|
Thanks for cleaning up the comments and commit messages. The description by registers and steps reads well. The plan for |
Stacked on #1797 (aurora-wip merge for the J873g, which brings #1205's USB2 hosts). Review the last four commits.
The J873g's (Mac mini M6, T8152) front USB-C ports sit behind an on-board VL822 hub on ATC2. With #1205 the hub's USB2 side works through
usb-drd2. This adds its USB3 side:apple,t8152-aciophy-usb3).PHY_APPLE_ACIOPHY_USB3).usb2gets it as itsusb3-phyand dropsmaximum-speed = "high-speed".CONFIG_PHY_APPLE_ACIOPHY_USB3=min the shared defaults, which arm64: asahi: enable all native hardware defaults and guard coverage #1939'shardware-defaults-testsrequires of every native driver.Things to know
Testing (M6; with #1797 and the other J873g PRs this is the M6's default kernel)
apple-aciophy-usb3 383000000.phy: USB3 up).scripts/dtc/apple-dt-check.shagainst integration/aurora 0abc2f3, with Merge aurora-wip 210c8f6e into integration/aurora (J873g NVMe, 10GbE, power off, USB2, audio) #1797 and the stacked J873g PRs: 0 new CHECK_DTBS warnings (8 fewer), and all 21 changed bindings pass dt_binding_check.tools/asahi/run-host-tests.pypasses 427/427 (with Merge aurora-wip 210c8f6e into integration/aurora (J873g NVMe, 10GbE, power off, USB2, audio) #1797 and the stacked J873g PRs, on 0abc2f3).defconfigplusasahi.configresolves toCONFIG_PHY_APPLE_ACIOPHY_USB3=m.--strictis clean apart from the MAINTAINERS hint.cc @Acelogic @RyanTheTide @DjDeveloperr @LiamRay10